{"id":25600,"date":"2023-02-09T21:41:07","date_gmt":"2023-02-09T21:41:07","guid":{"rendered":"https:\/\/the3dsourced.wpengine.com\/?p=25600"},"modified":"2023-02-17T12:44:04","modified_gmt":"2023-02-17T12:44:04","slug":"petg-stringing","status":"publish","type":"post","link":"https:\/\/www.3dsourced.com\/guides\/petg-stringing\/","title":{"rendered":"4 Ways To Fix PETG Stringing (Solves 90% of Problems)"},"content":{"rendered":"<p>Stringing can happen in all filaments, but PETG stringing is more common than most others. When it happens, you&#8217;ll see unwanted, thin, plastic strands on your 3D printed object.&nbsp;<\/p>\n\n\n\n<p><strong>Stringing in PETG occurs when molten filament oozes from the nozzle as it moves between two points, resulting in hair-like strings of plastic on your print. This over-extrusion may also create blobs &#8211; little bumps on your print that can ruin its surface finish.<\/strong><\/p>\n\n\n\n<p>But why is PETG particularly prone to stringing?<\/p>\n\n\n\t\t\t\t<div class=\"wp-block-uagb-table-of-contents uagb-toc__align-left uagb-toc__columns-1 uagb-toc__collapse uagb-block-b69da96e\"\n\t\t\t\t\tdata-scroll= \"1\"\n\t\t\t\t\tdata-offset= \"30\"\n\t\t\t\t\tstyle=\"\"\n\t\t\t\t>\n\t\t\t\t<div class=\"uagb-toc__wrap\">\n\t\t\t\t\t\t<div class=\"uagb-toc__title\">\n\t\t\t\t\t\t\tTable Of Contents\t\t\t\t\t\t\t\t\t\t\t\t\t<svg xmlns=\"https:\/\/www.w3.org\/2000\/svg\" viewbox= \"0 0 384 512\"><path d=\"M192 384c-8.188 0-16.38-3.125-22.62-9.375l-160-160c-12.5-12.5-12.5-32.75 0-45.25s32.75-12.5 45.25 0L192 306.8l137.4-137.4c12.5-12.5 32.75-12.5 45.25 0s12.5 32.75 0 45.25l-160 160C208.4 380.9 200.2 384 192 384z\"><\/path><\/svg>\n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<div class=\"uagb-toc__list-wrap\">\n\t\t\t\t\t\t<ol class=\"uagb-toc__list\"><li class=\"uagb-toc__list\"><a href=\"#petg-stringing-issues\">PETG Stringing Issues<\/a><\/li><li class=\"uagb-toc__list\"><a href=\"#how-do-i-stop-stringing-in-petg\">How Do I Stop Stringing in PETG?<\/a><\/li><ul class=\"uagb-toc__list\"><li class=\"uagb-toc__list\"><a href=\"#1-adjust-nozzle-temperature\">1. Adjust Nozzle Temperature<\/a><\/li><ul class=\"uagb-toc__list\"><li class=\"uagb-toc__list\"><a href=\"#why-it-affects-petg-stringing\">Why it affects PETG Stringing:<\/a><\/li><li class=\"uagb-toc__list\"><a href=\"#how-to-fix\">How To Fix:<\/a><\/li><\/li><\/ul><li class=\"uagb-toc__list\"><a href=\"#2-adjust-travel-speed\">2. Adjust Travel Speed<\/a><\/li><ul class=\"uagb-toc__list\"><li class=\"uagb-toc__list\"><a href=\"#why-it-affects-petg-stringing\">Why it affects PETG Stringing:<\/a><\/li><li class=\"uagb-toc__list\"><a href=\"#how-to-fix\">How To Fix:<\/a><\/li><\/li><\/ul><li class=\"uagb-toc__list\"><a href=\"#3-adjust-retraction-settings\">3. Adjust Retraction Settings<\/a><\/li><ul class=\"uagb-toc__list\"><li class=\"uagb-toc__list\"><a href=\"#why-it-affects-petg-stringing\">Why it affects PETG Stringing:<\/a><\/li><li class=\"uagb-toc__list\"><a href=\"#how-to-fix\">How To Fix:<\/a><\/li><ul class=\"uagb-toc__list\"><li class=\"uagb-toc__list\"><a href=\"#retraction-speed\">Retraction Speed<\/a><\/li><li class=\"uagb-toc__list\"><a href=\"#retraction-distance\">Retraction Distance<\/a><\/li><li class=\"uagb-toc__list\"><a href=\"#retraction-minimum-travel-distance\">Retraction Minimum Travel Distance<\/a><\/li><li class=\"uagb-toc__list\"><a href=\"#vertical-lift\">Vertical Lift<\/a><\/li><\/li><\/ul><\/li><\/ul><li class=\"uagb-toc__list\"><a href=\"#4-keep-your-petg-dry\">4. Keep Your PETG Dry<\/a><\/li><ul class=\"uagb-toc__list\"><li class=\"uagb-toc__list\"><a href=\"#why-it-affects-petg-stringing\">Why it affects PETG Stringing:<\/a><\/li><li class=\"uagb-toc__list\"><a href=\"#how-to-fix\">How To Fix:<\/a><\/li><\/li><\/ul><\/li><\/ul><\/li><li class=\"uagb-toc__list\"><a href=\"#how-do-i-stop-my-petg-from-blobbing-and-leaving-zits\">How Do I Stop My PETG From Blobbing And Leaving Zits?<\/a><\/li><li class=\"uagb-toc__list\"><a href=\"#how-to-fix-petg-stringing-on-the-ender-3\">How To Fix PETG Stringing on the Ender 3<\/a><\/li><ul class=\"uagb-toc__list\"><li class=\"uagb-toc__list\"><a href=\"#petg-stringing-on-the-ender-3-pro\">PETG Stringing on the Ender 3 Pro<\/a><\/li><li class=\"uagb-toc__list\"><a href=\"#petg-stringing-on-the-ender-3-v2\">PETG Stringing on the Ender 3 V2<\/a><\/li><\/li><\/ul><\/li><\/ul><\/li><\/ul><\/li><li class=\"uagb-toc__list\"><a href=\"#how-to-fix-petg-stringing-on-ender-5\">How To Fix PETG Stringing on Ender 5<\/a><\/li><li class=\"uagb-toc__list\"><a href=\"#how-to-fix-petg-stringing-on-prusa\">How to Fix PETG Stringing on Prusa<\/a><\/li><li class=\"uagb-toc__list\"><a href=\"#faqs\">FAQs<\/a><\/li><ul class=\"uagb-toc__list\"><li class=\"uagb-toc__list\"><a href=\"#what-is-a-good-retraction-for-petg\">What is a good retraction for PETG?\u00a0<\/a><\/li><li class=\"uagb-toc__list\"><a href=\"#how-do-i-get-petg-to-print-smoother\">How do I get PETG to print smoother?<\/a><\/li><\/ul><\/ul><\/ul><\/ul><\/ol>\t\t\t\t\t<\/div>\n\t\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\n\n\n<h2>PETG Stringing Issues<\/h2>\n\n\n\n<p>Compared to other filaments, PETG has a higher chance of stringing because of its high printing temperature (220 &#8211; 250\u00b0C). At such high temperatures, PETG is relatively <em>more fluid<\/em>. This makes it ooze smoothly out of the nozzle even when it shouldn&#8217;t, resulting in stringing.<\/p>\n\n\n\n<p>But stringing shouldn&#8217;t always be the case while printing with PETG. Here are a few things you can do to stop it.<\/p>\n\n\n<div class=\"gb-container gb-container-17f5da06 no-title-margin gb-container-3ce39208\" id=\"question-box-pattern\"><div class=\"gb-inside-container\">\n<div class=\"gb-grid-wrapper gb-grid-wrapper-cb7186aa gb-grid-wrapper-13867f42\">\n<div class=\"gb-grid-column gb-grid-column-aa6aefb5 gb-grid-column-44ad68b8\"><div class=\"gb-container gb-container-aa6aefb5 gb-container-44ad68b8\"><div class=\"gb-inside-container\">\n\n<figure class=\"gb-block-image gb-block-image-a1cd5870\"><img decoding=\"async\" loading=\"lazy\" width=\"256\" height=\"256\" class=\"gb-image gb-image-a1cd5870 gb-image-01dc0c8a\" src=\"https:\/\/www.3dsourced.com\/wp-content\/uploads\/2022\/10\/circle-wavy-question-duotone.svg\" alt=\"\" title=\"circle-wavy-question-duotone\"\/><\/figure>\n\n<\/div><\/div><\/div>\n\n<div class=\"gb-grid-column gb-grid-column-5b8fa74e gb-grid-column-f8c4bfec\"><div class=\"gb-container gb-container-5b8fa74e gb-container-f8c4bfec\"><div class=\"gb-inside-container\">\n\n<h2 class=\"gb-headline gb-headline-5fa8a6ad gb-headline-text gb-headline-ec198c29\">How Do I Stop Stringing in PETG?<\/h2>\n\n<\/div><\/div><\/div>\n<\/div>\n\n\n<p class=\"gb-headline gb-headline-fd676b74 gb-headline-text gb-headline-168631b7\">You can stop PETG stringing by adjusting your nozzle temperature, travel speed, and retraction settings. You can also prevent it by using high-quality PETG filaments and always keeping them dry.<\/p>\n\n<\/div><\/div>\n\n\n<p>Read on to find out how you can put a final stop to stringing whenever you print with PETG. The 4 main fixes are:<\/p>\n\n\n\n<ol>\n<li><a href=\"#adjust-nozzle-temperature\" data-type=\"internal\" data-id=\"#adjust-nozzle-temperature\">Adjust nozzle temperature<\/a><\/li>\n\n\n\n<li><a href=\"#travel-speed\" data-type=\"internal\" data-id=\"#travel-speed\">Adjust extruder travel speed<\/a><\/li>\n\n\n\n<li><a href=\"#adjust-retraction-settings\" data-type=\"internal\" data-id=\"#adjust-retraction-settings\">Change your retraction settings<\/a><\/li>\n\n\n\n<li><a href=\"#keep-petg-dry\" data-type=\"internal\" data-id=\"#keep-petg-dry\">Keep your PETG filament dry<\/a><\/li>\n<\/ol>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity is-style-dots\"\/>\n\n\n\n<h3 id=\"adjust-nozzle-temperature\">1. Adjust Nozzle Temperature<\/h3>\n\n\n\n<figure class=\"wp-block-image size-full\"><img decoding=\"async\" loading=\"lazy\" width=\"800\" height=\"400\" src=\"https:\/\/www.3dsourced.com\/wp-content\/uploads\/2023\/02\/Different-temperatures-affecting-PETG-stringing-differently.jpeg\" alt=\"How different nozzle temperatures affect PETG stringing differently\" class=\"wp-image-25621\" srcset=\"https:\/\/www.3dsourced.com\/wp-content\/uploads\/2023\/02\/Different-temperatures-affecting-PETG-stringing-differently.jpeg 800w, https:\/\/www.3dsourced.com\/wp-content\/uploads\/2023\/02\/Different-temperatures-affecting-PETG-stringing-differently-300x150.jpeg 300w, https:\/\/www.3dsourced.com\/wp-content\/uploads\/2023\/02\/Different-temperatures-affecting-PETG-stringing-differently-768x384.jpeg 768w\" sizes=\"(max-width: 800px) 100vw, 800px\" \/><\/figure>\n\n\n\n<h4>Why it affects PETG Stringing:<\/h4>\n\n\n\n<p>When it comes to 3D printing with PETG filament, the nozzle temperature is one of the most important factors to consider. Too low, and you&#8217;ll find that your print quality drops. Too high, and your filament will overflow and create strings.&nbsp;<\/p>\n\n\n\n<p>Generally, PETG prints between 220\u00b0C and 250\u00b0C, but how do you get the perfect nozzle temperature for your PETG prints?<\/p>\n\n\n\n<h4>How To Fix:<\/h4>\n\n\n\n<p>To get the best results, the nozzle temperature should be just high enough to ensure the filament melts and flows correctly while adhering to the build plate. A good place to start is at about 245\u00b0C, though nozzle temperature will vary slightly depending on your printer and filament brand.<\/p>\n\n\n\n<p>To get a good sense of the correct nozzle temperature for your printer and filament brand, use a <a href=\"https:\/\/www.thingiverse.com\/thing:2862812\" target=\"_blank\" rel=\"noopener\" data-lasso-id=\"23942\">temperature tower test<\/a>.&nbsp;<\/p>\n\n\n\n<p>The test instructs your printer to print a tower of multiple blocks. Each block is printed at a different temperature, with the base printed at the highest temperature. As the tower rises, the printing temperature drops by 5\u00b0C up to the final block at the top.<\/p>\n\n\n\n<p>When the print is done, physically analyze it and decide your optimal printing temperature based on which block has the highest print quality.<\/p>\n\n\n\n<h3 id=\"travel-speed\">2. Adjust Travel Speed<\/h3>\n\n\n\n<figure class=\"wp-block-image size-full\"><img decoding=\"async\" loading=\"lazy\" width=\"800\" height=\"400\" src=\"https:\/\/www.3dsourced.com\/wp-content\/uploads\/2023\/02\/image-10.png\" alt=\"How travel speed affects stringing on the Ender 3 V2 Neo\" class=\"wp-image-25637\" srcset=\"https:\/\/www.3dsourced.com\/wp-content\/uploads\/2023\/02\/image-10.png 800w, https:\/\/www.3dsourced.com\/wp-content\/uploads\/2023\/02\/image-10-300x150.png 300w, https:\/\/www.3dsourced.com\/wp-content\/uploads\/2023\/02\/image-10-768x384.png 768w\" sizes=\"(max-width: 800px) 100vw, 800px\" \/><figcaption class=\"wp-element-caption\">We recently tested the Ender 3 V2 Neo, and you can see the differences in stringing at 90mm\/s vs 60mm\/s.<\/figcaption><\/figure>\n\n\n\n<h4>Why it affects PETG Stringing:<\/h4>\n\n\n\n<p>Travel speed refers to how fast the nozzle moves between gaps when it&#8217;s not extruding filament.&nbsp;<\/p>\n\n\n\n<p>It&#8217;s essential to keep your travel speed reasonable for PETG because if the speed is too slow, your nozzle will have more time to drool out the melting filament. If the speed is too fast, print quality drops. <\/p>\n\n\n\n<p>But if you&#8217;re printing at a reasonable speed, the nozzle will move quickly enough before the melting filament oozes and forms <a data-lasso-id=\"23943\" href=\"https:\/\/www.3dsourced.com\/rigid-ink\/3d-prints-pillowing-stringing-layers-splitting-solved\/\" target=\"_blank\" rel=\"noopener\">strings and blobs<\/a>.<\/p>\n\n\n\n<p>You can see in the image above how increasing speed leads to more stringing in the final part. This was from a recent review we did of the <a href=\"https:\/\/www.3dsourced.com\/3d-printer-reviews\/ender-3-v2-neo-review\/\" target=\"_blank\" data-type=\"post\" data-id=\"22051\" rel=\"noopener\" data-lasso-id=\"27095\">Creality Ender 3 V2 Neo<\/a>, and applies to all 3D printers.<\/p>\n\n\n\n<h4>How To Fix:<\/h4>\n\n\n\n<p>Starting at around 90 mm\/s, try increasing the printer&#8217;s travel speed gradually by 10 mm\/s until you no longer notice any stringing or blobs.<\/p>\n\n\n\n<h3 id=\"adjust-retraction-settings\">3. Adjust Retraction Settings<\/h3>\n\n\n\n<figure class=\"wp-block-image size-full\"><img decoding=\"async\" loading=\"lazy\" width=\"800\" height=\"400\" src=\"https:\/\/www.3dsourced.com\/wp-content\/uploads\/2023\/02\/image-9.png\" alt=\"Retraction settings for the Ender 3\" class=\"wp-image-25622\" srcset=\"https:\/\/www.3dsourced.com\/wp-content\/uploads\/2023\/02\/image-9.png 800w, https:\/\/www.3dsourced.com\/wp-content\/uploads\/2023\/02\/image-9-300x150.png 300w, https:\/\/www.3dsourced.com\/wp-content\/uploads\/2023\/02\/image-9-768x384.png 768w\" sizes=\"(max-width: 800px) 100vw, 800px\" \/><figcaption class=\"wp-element-caption\">Retraction settings for the Ender 3.<\/figcaption><\/figure>\n\n\n\n<h4>Why it affects PETG Stringing:<\/h4>\n\n\n\n<p>Retraction is the process of pulling the filament back up the nozzle after a move is completed. This prevents the plastic from being extruded while the nozzle is stopped, which reduces stringing.&nbsp;<\/p>\n\n\n\n<p>The amount of retraction you&#8217;ll need can vary depending on your printer, filament, and model, so it&#8217;s better to experiment to find the best settings. So, where do you start?&nbsp;<\/p>\n\n\n\n<p>There are four retraction settings you can tweak to control stringing. You can run a simple <a href=\"https:\/\/www.printables.com\/model\/282899-stringing-test-petg\" target=\"_blank\" rel=\"noopener\" data-lasso-id=\"23944\">stringing test<\/a> and see how the stringing changes as you change the following settings:&nbsp;<\/p>\n\n\n\n<h4>How To Fix:<\/h4>\n\n\n\n<h5>Retraction Speed<\/h5>\n\n\n\n<p>Retraction speed is how fast the filament is pulled back whenever the nozzle moves between areas where no extrusion will occur. You want your filament to retract quickly before it has time to drip out in places it&#8217;s not supposed to.<\/p>\n\n\n\n<p>With PETG, a retraction speed of 25 to 40 mm\/s on Bowden tube extruders can get the job done without causing any stringing. On the other hand, direct drive extruders push the filament directly into the nozzle without going through a tube. Therefore, a retraction speed of 25 to 35 mm\/s is enough to prevent stringing.&nbsp;<\/p>\n\n\n\n<h5>Retraction Distance<\/h5>\n\n\n\n<p>Retraction distance refers to how far back the filament is pulled away from the nozzle as it travels. Bowden extruders need about 2 to 5 mm of retraction distance. Direct drive extruders require 1 to 2 mm.<\/p>\n\n\n\n<h5>Retraction Minimum Travel Distance<\/h5>\n\n\n\n<p>This refers to the minimum distance your extruder has to travel before retraction occurs. If this distance is too much, it may prevent any retraction from happening, while tiny distances will constantly trigger retraction and make the printing process slow. To get an optimal retraction minimum travel distance for PETG, start at 2 mm and reduce the distance gradually by 0.1 mm until you find a sweet spot where no strings are noticeable.<\/p>\n\n\n\n<h5>Vertical Lift<\/h5>\n\n\n\n<p>This feature lets the nozzle move up a small distance to create a gap between it and the object during short breaks in extrusion. Also called Z-hop, it is said to prevent the unwanted filament from dripping onto the object as it prints, reducing blobs and stringing.&nbsp;<\/p>\n\n\n\n<p>There are mixed opinions about its efficacy, but it certainly doesn\u2019t hurt to give it a shot. In some slicers, you can also configure the vertical lift distance, but that should be a last resort.<\/p>\n\n\n\n<h3 id=\"keep-petg-dry\">4. Keep Your PETG Dry<\/h3>\n\n\n\n<h4>Why it affects PETG Stringing:<\/h4>\n\n\n\n<p>It&#8217;s good practice to keep any filament dry, but it&#8217;s even more critical when working with PETG. This is because PETG has a greater tendency to absorb bits of moisture if left exposed in the open. Moisture expands PETG, causing clogging, nozzle damage, strings, blobs, and zits.<\/p>\n\n\n\n<h4>How To Fix:<\/h4>\n\n\n\n<p>It&#8217;s not always easy to create a moisture-free environment, but using a filament storage container can help. If you can&#8217;t immediately get one, keep the PETG away from humid, hot, and wet conditions.&nbsp;<\/p>\n\n\n\n<p>If you suspect that your PETG has become moist, you can use a filament dryer to restore it to its dry state. Some of the best filament dryers we recommend include:<\/p>\n\n\n\n<ul>\n<li><a href=\"https:\/\/www.matterhackers.com\/store\/l\/printdry-filament-drying-system\/sk\/MNXQRWQC?aff=7512\" target=\"_blank\" rel=\"nofollow sponsored noopener\" data-lasso-id=\"23945\">PrintDry Filament Drying System<\/a>, which allows you to dry wet filament in real-time as you feed it to your 3D printer. It also comes with a vacuum-sealed container and air removal pump to keep your dry filament dry.<\/li>\n\n\n\n<li><a data-lasso-id=\"23946\" href=\"https:\/\/amzn.to\/3811fHN\" target=\"_blank\" rel=\"nofollow sponsored noopener\">PolyMaker Filament Storage Box II<\/a>, which includes a storage box with a built-in high-precision thermo-hygrometer that lets you monitor humidity and temperature.<\/li>\n<\/ul>\n\n\n\n<div class=\"wp-block-affiliate-plugin-lasso\"><div id=\"lasso-anchor-id-23190-23958\" class=\"lasso-container\">\n    <!-- LASSO DISPLAY BOX (https:\/\/getlasso.co) -->\n\t<div class=\"lasso-display lasso-cactus lasso-url-printdry-pro-filament-drying-system-matterhackers \">\n\t\t<!-- BADGE -->\n\t\t\t\t\t<div class=\"lasso-badge\">\n\t\t\t\tBest Filament Dryer & Storage\t\t\t<\/div>\n\t\t\n\t\t<!-- LASSO TITLE, PRICE, DESC, AND IMAGE -->\n\t\t<div class=\"lasso-box-1\">\n\t\t\t\t\t\t\t\t\t\t\t<a class=\"lasso-title\" target=\"_blank\" href=\"https:\/\/www.3dsourced.com\/printdry-pro-filament-drying-system-matterhackers\/\" data-lasso-box-trackable=\"true\" data-lasso-id=\"23190\" data-lasso-name=\"PrintDry PRO Filament Drying System\" title=\"PrintDry PRO Filament Drying System\" rel=\"nofollow noopener sponsored\">\n\t\t\t\t\tPrintDry PRO Filament Drying System\t\t\t\t<\/a>\n\t\t\t\t\t\t\t\n\t\t\t\n\t\t\t\t\t\t\t<div class=\"lasso-price\">\n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<div class=\"lasso-price-value\">\n\t\t\t\t\t\t\t<span class=\"discount-price\"><\/span>\n\t\t\t\t\t\t\t<span class=\"latest-price\">$189.00<\/span>\n\t\t\t\t\t\t<\/div>\n\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t\t\t<div class=\"clear\"><\/div>\n\t\t\t\n\t\t\t\t\t<\/div>\n\n\t\t<div class=\"lasso-box-2\">\n\t\t\t<a class=\"lasso-image\" target=\"_blank\" href=\"https:\/\/www.3dsourced.com\/printdry-pro-filament-drying-system-matterhackers\/\" data-lasso-box-trackable=\"true\" data-lasso-id=\"23190\" data-lasso-name=\"PrintDry PRO Filament Drying System\" title=\"PrintDry PRO Filament Drying System\" rel=\"nofollow noopener sponsored\">\n\t\t\t\t<img src=\"https:\/\/www.3dsourced.com\/wp-content\/uploads\/2022\/02\/Screenshot-2022-02-28-at-18-21-36-filament-dryer-hm-jpg-JPEG-Image-800-\u00d7-700-pixels.webp\" height=\"500\" width=\"500\" loading=\"lazy\" alt=\"PrintDry PRO Filament Drying System\">\n\t\t\t<\/a>\n\t\t<\/div>\n\n\t\t<!-- BUTTONS -->\n\t\t<div class=\"lasso-box-3\">\n\t\t\t<a class=\"lasso-button-1\" target=\"_blank\" href=\"https:\/\/www.3dsourced.com\/printdry-pro-filament-drying-system-matterhackers\/\" data-lasso-box-trackable=\"true\" data-lasso-id=\"23190\" data-lasso-name=\"PrintDry PRO Filament Drying System\" title=\"PrintDry PRO Filament Drying System\" rel=\"nofollow noopener sponsored\">\n\t\t\t\tMatterhackers here\t\t\t<\/a>\n\t\t<\/div>\n\n\t\t<div class=\"lasso-box-4\">\n\t\t\t\t\t<\/div>\n\n\t\t<!-- DISCLOSURE & DATE -->\n\t\t\t\t\t<div class=\"lasso-box-5\">\n\t\t\t\t<div class=\"lasso-disclosure\">\n\t\t\t\t\t<span>We earn a commission if you make a purchase, at no additional cost to you.<\/span>\t\t\t\t<\/div>\n\t\t\t<\/div>\n\t\t\n\t\t<div class=\"lasso-box-6\">\n\t\t\t<div class=\"lasso-date\">\n\t\t\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t<\/div>\n<\/div>\n<\/div>\n\n\n\n<h2>How Do I Stop My PETG From Blobbing And Leaving Zits?<\/h2>\n\n\n\n<p>PETG zits and first-layer blobs commonly happen alongside stringing, so they are also preventable. The lumps and zits appear as small bumps on the surface of your printed objects.&nbsp;<\/p>\n\n\n\n<p>They happen when the filament pressure remains high during retraction, causing a short burst of melted filament to get into a printed layer. This over-extrusion of filament shows up as a blob, zit, or some blemish in your print.<\/p>\n\n\n\n<p>Just like stringing, you can prevent PETG zits and blobs by adjusting your nozzle temperature, travel speed, and retraction settings. Also, ensure your nozzle is clean because any residue or build-up can lead to blobs and zits. You should also slow your printing speed to about 40 &#8211; 60 mm\/s.<\/p>\n\n\n\n<p>Lastly, consider upgrading your filament if you want to reduce PETG stringing. We often underlook the quality of filament when troubleshooting printing problems, yet, it&#8217;s often the first line of defense against bad prints.&nbsp;<\/p>\n\n\n\n<p>If you\u2019re printing as a hobbyist, that\u2019s okay. But if you want to take your print quality to the next level, you need to work with some of the best PETG filaments out there. Here are a few that have stood the test of time &#8211; and quality:<\/p>\n\n\n\n<ul>\n<li><a href=\"https:\/\/www.matterhackers.com\/store\/c\/175mm-petg?aff=7512\" target=\"_blank\" rel=\"nofollow sponsored noopener\" data-lasso-id=\"23947\">Matterhackers USA PETG filament range<\/a><\/li>\n\n\n\n<li><a href=\"https:\/\/www.matterhackers.com\/store\/c\/1.75mm%20PRO%20Series%20PETG\" target=\"_blank\" rel=\"nofollow sponsored noopener\" data-lasso-id=\"23948\">Matterhackers USA PRO Series PETG<\/a><\/li>\n\n\n\n<li><a href=\"https:\/\/www.amazon.com\/OVERTURE-Filament-Consumables-Dimensional-Accuracy\/dp\/B07PGYHYV8?tag=3dsourced-20\" target=\"_blank\" data-type=\"URL\" data-id=\"https:\/\/www.amazon.com\/OVERTURE-Filament-Consumables-Dimensional-Accuracy\/dp\/B07PGYHYV8?tag=3dsourced-20\" rel=\"nofollow sponsored noopener\" data-lasso-id=\"23949\">Overture PETG filament<\/a><\/li>\n<\/ul>\n\n\n\n<h2>How To Fix PETG Stringing on the Ender 3<\/h2>\n\n\n\n<h3>PETG Stringing on the Ender 3 Pro<\/h3>\n\n\n\n<p>If you\u2019re working with an Ender 3 Pro, try these settings to fix PETG stringing:<\/p>\n\n\n\n<ul>\n<li><strong>Bed temperature:<\/strong> 85 \u00b0C<\/li>\n\n\n\n<li><strong>Nozzle temperature:<\/strong> 220 &#8211; 240 \u00b0C. PETG prints between 220\u00b0C and 250\u00b0C, but a temperature above 245 \u00b0C might cause nozzle damage.<\/li>\n\n\n\n<li><strong>Retraction distance:<\/strong> 6 &#8211; 6.5mm.<\/li>\n\n\n\n<li><strong>Retraction speed:<\/strong> \u226440 mm\/s<\/li>\n\n\n\n<li><strong>Print speed: <\/strong>30mm\/s \u2013 50mm\/s<\/li>\n<\/ul>\n\n\n\n<h3>PETG Stringing on the Ender 3 V2<\/h3>\n\n\n\n<p>Many of the print settings on the Ender 3 Pro will work on Ender 3 V2. However, the Ender 3 V2 has a carborundum glass plate, which has implications if you use PETG.&nbsp;<\/p>\n\n\n\n<p>PETG sticks so easily to glass that it can even fuse into the glass plate itself. Over prolonged use, you&#8217;ll notice residues on the glass, which can spoil your first layer finish.&nbsp;<\/p>\n\n\n\n<p>To stop this issue, we recommend using a glue stick or some good old blue painter&#8217;s tape on the build plate. Then, set the bed temperature at about 85\u00b0C to get a proper adhesion on your print. If you want more details on getting excellent adhesion with PETG, have a look at this <a href=\"https:\/\/www.3dsourced.com\/guides\/petg-not-sticking-to-bed\/\" target=\"_blank\" rel=\"noopener\" data-lasso-id=\"23950\">PETG adhesion guide<\/a>.<\/p>\n\n\n\n<h2>How To Fix PETG Stringing on Ender 5<\/h2>\n\n\n\n<p>On your Ender 5, use the same print settings as you would on an Ender 3. In addition, try adding cooling to your printing process. This will help the filament to cool more quickly, reducing the amount of stringing.<\/p>\n\n\n\n<h2>How to Fix PETG Stringing on Prusa<\/h2>\n\n\n\n<p>There are several ways to reduce <a href=\"https:\/\/help.prusa3d.com\/article\/stringing-and-oozing_1805\" target=\"_blank\" rel=\"noopener\" data-lasso-id=\"23951\">stringing and oozing on your Prusa<\/a>. But the most essential methods include optimizing your retraction settings and printing at a temperature of 220\u00b0C &#8211; 250\u00b0C. If you&#8217;re using the MK2.5\/S or MK3\/S\/+, keep your retraction at a maximum of 2 mm.<\/p>\n\n\n\n<p>You can also try sequential printing, which allows you to print each part separately and reduce stringing. To activate sequential printing on your Prusa, go to <em>Print settings -&gt; Output options -&gt; Sequential printing.<\/em><\/p>\n\n\n\n<h2>FAQs<\/h2>\n\n\n<div id=\"rank-math-faq\" class=\"rank-math-block\">\n<div class=\"rank-math-list\">\n<div id=\"faq-question-1675966347569\" class=\"rank-math-list-item\">\n<h3 class=\"rank-math-question\"><strong>What is a good retraction for PETG?\u00a0<\/strong><\/h3>\n<div class=\"rank-math-answer\">\n\n<p>With PETG, a retraction speed of 25 to 40 mm\/s on Bowden tube extruders can get the job done without causing any stringing.<\/p>\n\n<\/div>\n<\/div>\n<div id=\"faq-question-1675966355052\" class=\"rank-math-list-item\">\n<h3 class=\"rank-math-question\"><strong>How do I get PETG to print smoother?<\/strong><\/h3>\n<div class=\"rank-math-answer\">\n\n<p>You can get PETG to print smoother by keeping your filament dry, reducing nozzle temperature, and optimizing retraction.<\/p>\n\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n\n\n<p>Related articles:<\/p>\n\n\n\n<ul>\n<li><a href=\"https:\/\/www.3dsourced.com\/3d-printer-materials\/petg-filament\/\" target=\"_blank\" data-type=\"post\" data-id=\"4404\" rel=\"noopener\" data-lasso-id=\"27817\">Complete PETG filament guide<\/a><\/li>\n\n\n\n<li><a href=\"https:\/\/www.3dsourced.com\/guides\/3d-print-shrinkage-pla-abs-petg\/\" target=\"_blank\" data-type=\"post\" data-id=\"18327\" rel=\"noopener\" data-lasso-id=\"27818\">PETG shrinkage<\/a><\/li>\n<\/ul>","protected":false},"excerpt":{"rendered":"<p>Stringing can happen in all filaments, but PETG stringing is more common than most others. When it happens, you&#8217;ll see unwanted, thin, plastic strands on your 3D printed object.&nbsp; Stringing in PETG &#8230; <a title=\"4 Ways To Fix PETG Stringing (Solves 90% of Problems)\" class=\"read-more\" href=\"https:\/\/www.3dsourced.com\/guides\/petg-stringing\/\" aria-label=\"More on 4 Ways To Fix PETG Stringing (Solves 90% of Problems)\">Read more<\/a><\/p>\n","protected":false},"author":24,"featured_media":25625,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"om_disable_all_campaigns":false,"_uag_custom_page_level_css":""},"categories":[7,2],"tags":[],"featured_post":[],"post_template":[56],"acf":[],"uagb_featured_image_src":{"full":["https:\/\/www.3dsourced.com\/wp-content\/uploads\/2023\/02\/PETG-Stringing.jpeg",1280,720,false],"thumbnail":["https:\/\/www.3dsourced.com\/wp-content\/uploads\/2023\/02\/PETG-Stringing-150x150.jpeg",150,150,true],"medium":["https:\/\/www.3dsourced.com\/wp-content\/uploads\/2023\/02\/PETG-Stringing-300x169.jpeg",300,169,true],"medium_large":["https:\/\/www.3dsourced.com\/wp-content\/uploads\/2023\/02\/PETG-Stringing-768x432.jpeg",768,432,true],"large":["https:\/\/www.3dsourced.com\/wp-content\/uploads\/2023\/02\/PETG-Stringing-1024x576.jpeg",1024,576,true],"1536x1536":["https:\/\/www.3dsourced.com\/wp-content\/uploads\/2023\/02\/PETG-Stringing.jpeg",1280,720,false],"2048x2048":["https:\/\/www.3dsourced.com\/wp-content\/uploads\/2023\/02\/PETG-Stringing.jpeg",1280,720,false]},"uagb_author_info":{"display_name":"Bruno Sekyanzi","author_link":"https:\/\/www.3dsourced.com\/author\/bruno-sekyanzi\/"},"uagb_comment_info":1,"uagb_excerpt":"Stringing can happen in all filaments, but PETG stringing is more common than most others. When it happens, you&#8217;ll see unwanted, thin, plastic strands on your 3D printed object.&nbsp; Stringing in PETG ... Read more","_links":{"self":[{"href":"https:\/\/www.3dsourced.com\/wp-json\/wp\/v2\/posts\/25600"}],"collection":[{"href":"https:\/\/www.3dsourced.com\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.3dsourced.com\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.3dsourced.com\/wp-json\/wp\/v2\/users\/24"}],"replies":[{"embeddable":true,"href":"https:\/\/www.3dsourced.com\/wp-json\/wp\/v2\/comments?post=25600"}],"version-history":[{"count":1,"href":"https:\/\/www.3dsourced.com\/wp-json\/wp\/v2\/posts\/25600\/revisions"}],"predecessor-version":[{"id":26542,"href":"https:\/\/www.3dsourced.com\/wp-json\/wp\/v2\/posts\/25600\/revisions\/26542"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.3dsourced.com\/wp-json\/wp\/v2\/media\/25625"}],"wp:attachment":[{"href":"https:\/\/www.3dsourced.com\/wp-json\/wp\/v2\/media?parent=25600"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.3dsourced.com\/wp-json\/wp\/v2\/categories?post=25600"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.3dsourced.com\/wp-json\/wp\/v2\/tags?post=25600"},{"taxonomy":"featured_post","embeddable":true,"href":"https:\/\/www.3dsourced.com\/wp-json\/wp\/v2\/featured_post?post=25600"},{"taxonomy":"post_template","embeddable":true,"href":"https:\/\/www.3dsourced.com\/wp-json\/wp\/v2\/post_template?post=25600"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}